 | Percy Gaillemard L. Smith - 1879 - 548 pages
...cut lengthways or crossways of the plates, to have an ultimate tensile strength of not less th:in 2G and not exceeding 30 tons per square inch of section, with an elongation of 20 per cent in length of ei^'ht inches. 2. Tempering Tests. — Strips cut lengthways of the plates 1J inch wide,... | |
 | Royal Institution of Naval Architects - Naval architecture - 1880 - 338 pages
...adoption in shipbuilding material. APPENDIX. ADMIRALTY TESTS FOR PLATE, ANGLE, BULB, AND BAR STEEL. Strips cut lengthwise or crosswise, to have an ultimate...with an elongation of 20 per cent, in a length of 8 inches. The beam, angle, bulb, and bar steel to stand such forge tests, both hot and cold, as may be... | |
 | James Stephen Jeans - Steel - 1880 - 966 pages
...as follows : — Tensile and Extension Teds. — 1. Strips cut lengthwise or crosswise of the plate to have an ultimate tensile strength of not less than...with an elongation of 20 per cent, in a length of 8 inches. Tempering Tests. — 2. Strips cut lengthwise of the plate, 1^ inch wide, heated uniformly... | |
 | Marine engineering - 1880 - 556 pages
...adoption in shipbuilding material. APPENDIX. ADMIRALTY TESTS FOR PLATE, ANGLE, BULB, AND BAR STEEL. Strips cut lengthwise or crosswise, to have an ultimate...square inch of section, with an elongation of 20 per ceni, in a length of 8 inches. The beam, angle, bulb, and bar steel to stand such forge tests, both... | |
 | James Stephen Jeans - Steel - 1880 - 962 pages
...inch. The tensile strength of the steel in the boilers referred to is reported to be from 38 to 40 tons per square inch of section, with an elongation of 20 per cent, on a length of 4 inches. The holes were all drilled in the plates and the rivets were of iron. For... | |
 | Institution of Civil Engineers (Great Britain) - Civil engineering - 1882 - 582 pages
...advantage. The Admiralty specification for plates and beams requires : — " Strips cut lengthwise to have an ultimate tensile strength of not less than...with an elongation of 20 per cent. in a length of 8 inches. " Strips cut crosswise or lengthwise 1 £ inch wide, heated uniformly to a low cherry-red and... | |
 | Hilary Bauerman - Iron - 1882 - 588 pages
...Strips cut lengthwise or crosswise to have an ultimate tensile strength of not less than 26 or more than 30 tons per square inch of section, with an elongation of 20 per cent, in a length of 8 inches. Beam, angle, bulb, and bar steel to satisfy such forge tests, hot and cold, as may be sufficient... | |
 | United States. Bureau of Naval Personnel - Marine engineering - 1883 - 224 pages
...adoption in ship-building material. APPENDIX. ADMIRALTY TESTS FOR PLATE, ANGLE, BULB, AND BAR STEEL. Strips cut lengthwise or crosswise, to have an ultimate...with an elongation of 20 per cent. in a length of 8 inches. ' . The beam, angle, bulb, and bar steel to stand such forge tests, both hot and cold, as may... | |
 | Engineering - 1883 - 568 pages
...with advantage. The Admiralty specification for plates and beams requires : " Strips cut lengthwise to have an ultimate tensile strength of not less than...with an elongation of 20 per cent, in a length of 8 inches. '• Strips cut crosswise or lengthwise 1£ inch wide, heated uniformly to a low cherry-red... | |
 | B. Martell, United States. Bureau of Naval Personnel - Marine steel - 1883 - 218 pages
...AND BAR STEEL. Strips cut lengthwise or crosswise, to have au ultimate tensile strength of not lese than 26 and not exceeding 30 tons per square inch...with an elongation of 20 per cent. in a length of 8 inches. The beam, angle, bulb, and bar steel to stand such forge tests, both hot and cold, as may be... | |
| |
Strips cut lengthwise or crosswise of the plate to have an ultimate tensile strength of not less than 26 and not exceeding 30 tons per square inch of section, with an elongation of 20 per cent in a length of 8 inches. * See " Manual of the Steam-engine, 
